A pressure washer cleaner is an indispensable appliance: you can use it to wash anything – a garage or utility room, a car that has just returned from an off-road raid, or a courtyard of a personal plot.
And some use this equipment even for carpet cleaning! A pressure washer is a good investment that will allow you to save on car washes for many years and save time when cleaning non-residential premises
It is not easy to use a pressure cleaner. But, if you follow the below ten best steps, you won’t find it hard to clean properly using a pressure washer;
- 1 1. Be familiar with the equipment
- 2 2.Adjust pressure
- 3 3.Select the perfect nozzle
- 4 4. Prepare your interior
- 5 5.Divide the places you want to clean
- 6 6. Use environmentally friendly cleaning products
- 7 7. Keep the nozzle at the appropriate angle
- 8 8.Scrub the persistent dirt
- 9 9. Use chemicals effectively
- 10 10.Seal
- 11 1.Pump
- 12 2.Electric motor
- 13 3.Circuit breaker and hoses
- 14 4. Do not forget about filtering
- 15 Detergent Supply
- 16 Conclusion
1. Be familiar with the equipment
Before starting to use a pressure washer cleaner, ensure that you are familiar with it. Read the manual that is usually provided. Test it first before purchasing it.
To wash any dirt, the machine has to be appropriately adjusted. The lowest pressure must be kept at approximately 1500 psi while maximum pressure at 1800 psi. This is because too much pressure may damage the surface.
3.Select the perfect nozzle
Each nozzle goes hand in hand with a particular pressure washer. Thus, ensure that you choose the best-fit one that will fit in the machine. Also, not all nozzles can be used in all jobs. Some are most suited for huge jobs like car washing, while others are suited for washing windows.
4. Prepare your interior
Ensure that you seal all the holes and cracks where you want to wash. Protect the lights, electric outlets, and switches too. This will help to prevent electrocution.
5.Divide the places you want to clean
If it is the walls, make sure that you divide it into sections first before embarking on your work. For instance, corners, downpipes, and windows. Start washing from top to bottom.
6. Use environmentally friendly cleaning products
You should not use products that can harm the environment. Ensure that you choose those cleaning products that are harmless to the surrounding. Apply the solution in one place then leave it for like 5 minutes for it to soak. Then, rinse the place with the pressure washer, then move to the next place.
7. Keep the nozzle at the appropriate angle
When the nozzle is not held at the right angle, it can damage the walls. Therefore, ensure that you hold it at 45 degrees and spray at a distance of 13 inches. If you feel like increasing the pressure, you should move further away from the surface.
8.Scrub the persistent dirt
If there is some persistent dirt, use a sponge or a brush to rub it off. Do not forget to use detergent too.
9. Use chemicals effectively
According to research, using pressure cleaners to apply chemicals on walls can destroy the wall. If at all you should use chemicals, ensure that they are pressure washer safe. Also, you should adjust the pressure to 50 psi.
Allow the washed place to dry properly and inspect. If you see water stains after one or two days, apply a product that is water repellant. This will help with adequate waterproofing.
This is the top 10 steps on using a pressure washer adequately. Ensure that you are familiar with them for a smooth washing.
Components of a pressure washer cleaner
A pressure washer is a fairly simple mobile device that is highly used in many areas. The main structural elements of the pressure washer are:
- Electrical engine;
- Pump with a motor circuit breaker;
- iii. Hose through which water is supplied;
- Hose with a high-pressure pistol grip;
- Housing with power cable;
Let’s see how these elements function among themselves, making the device as a whole work.
In the pressure washer, this can be installed as a piston, plunger, and any other pump. The efficiency of the entire pressure washer and its service life depends on the quality of the pump as a whole, and in particular, on the material of the pistons and piston chambers.
In low-cost models, single-piston pumps are more commonly used. And variants of devices of a more expensive price category, as a rule, are equipped with pumps with several plungers (pistons).
Another difference between the budget options of the unit is that the details of the piston are made of plastic and do not differ in durability. The premium segment washers use ceramic pistons or made of alloy steel, and the body is made of aluminum alloy.
Moreover, inexpensive models, the piston chambers, and the pistons themselves are highly compatible with each other. And the working surface of these parts is processed just perfectly.
An electric motor occupies almost the entire space inside the housing of a pressure washer. It also accounts for the bulk of the entire device. Traditionally, an engine with brushes is installed in the sink. But there are units and without brushes. Their fundamental difference is the development of a larger resource and less heat during operation.
One or two fans are installed on the motor axis. They are needed to cool the “heart” of the washing machine. In the case of using two fans, one draws in air from the outside, directing it along with the rotor. The second is used to drain hot air from the opposite end of the engine.
The shaft of the electric motor is connected to the gearbox. With its help, rotation from the shaft is transmitted to the pump (pump). In both cheap and expensive models of units, the gear housing is made of high-strength plastic.
3.Circuit breaker and hoses
The circuit breaker is connected to the pressure sensor and is an important element of the pump device. It is triggered when the sensor indicates an excess of the level allowed for operation, and the engine stops. And as soon as the pressure begins to fall, the “heart” of the sink starts again. The process of resuming the water supply starts instantly.
This device has two nozzles that are connected to the pump: inlet and outlet. The inlet pipe is connected with a hose to a source of water supply, which can be either a water supply system or a certain tank filled with water. A pressure hose with a pistol grip is connected to the outlet pipe.
4. Do not forget about filtering
Often, a washer cleaner device is connected to a source of technical water. This means that various impurities can be in the liquid. The use of such water can lead to malfunction and failure of the washing unit.
In order to prevent negative consequences, it is recommended to add one more element to the cleaning washer – a filter. It should be installed in front of the hose connected to the incoming pipe. And in special cases, experts recommend installing a coarse filter, and after it a second one for fine cleaning.
Thanks to various nozzles, the shape of the jet can be adjusted and changed. Parameters such as jet velocity and water flow are critical in determining the efficiency of the unit. And not pressure, as many believe. It turns out that the selected nozzle directly affects the quality of work on cleaning surfaces.
To choose a high-quality washer cleaner that meets your expectations, you first need to figure out what kind of appliance it is and what parts it consists of. In fact, a pressure washer is a complex technical device. Its main elements are the casing, motor, water supply pump, hose with washing nozzle, and cable.
The electric motor is the heart of a pressure washer; the capabilities of the device depend on its quality and power. As a rule, a high-pressure washer is equipped with it, but there are also battery models, as well as devices with an internal combustion engine. It is imperative that the motor has protection against voltage surges. Otherwise, it will not last long.
The pump is the element responsible for the pressure of water; that is, the pump creates pressure. Water under pressure enters the hose, ending with a nozzle gun, which changes the configuration and strength of the water flow. This is necessary for different types of work: actually washing, applying the foam, or removing an old thick layer of dirt
Pressure washers vary significantly in their characteristics. What points should you pay attention to when choosing such an apparatus?
First, you need to decide which model you want to buy – domestic or professional. Household is suitable for work on a personal plot, washing a car and the facade of a house, garden tools, etc. Such sinks are compact, designed for light loads, and the maximum pressure in them does not exceed 180 bar.
The pressure in professional models is greater, as are higher and indicators of flow volume and endurance. Such devices are sometimes equipped with a gasoline engine. They are suitable for use in construction conditions for utilities and industrial enterprises.
Particular attention should be paid to this characteristic since the convenience of working with the unit depends on the length of the hose. A hose up to four meters long is enough for washing the car, but if you need a wash for gardening and washing the facade of a country house, choose models with a longer hose – at least seven meters. In any case, you can always separately purchase an extension hose.
This indicator determines the pressure of water. The larger it is, the better the quality of cleaning. Even for domestic needs, for example, for washing a car, the pressure should not be lower than 130 bar. Otherwise, you will have to spend quite a lot of effort, water, and electricity to achieve the desired result.
It will also take a lot of time: sinks of a low class, as a rule, are air-cooled by the engine. Therefore they can work only 20 minutes without a break. But for some high-end models, the pressure is regulated directly at the sink.
This indicator indicates the consumption of water. High-pressure washers for domestic use typically spend 600 liters per hour. Professional models – one and a half to two times more.
A detergent is necessary for effective work, but the methods of its supply are different:
- A foam nozzle that is worn directly on the gun and is designed to apply active foam;
- An integrated hose that exits the sink body;
- Special seat under the container with detergent.
It should be noted that dense abundant foam will be obtained only when using a foam nozzle.
1.Water intake function
This function is absolutely necessary if you plan to take water from open sources or barrels, that is, from where there is no access to the water supply.
It is enough to place the washing hose in the water no more than five meters long with a non-return valve at the end, and the sink itself will take water. But you need to keep in mind that the distance from the surface of the water to the kink of the hose at the edge of the tank should not exceed half a meter.
2.Pump housing material
The most inexpensive material is plastic. It is lightweight, cheap, and not afraid of corrosion. It is believed that plastic is very fragile, and sinks made of this material are short-lived due to the formation of cracks on the body.
This is not entirely true, because it all depends on the quality of the plastic: the one used in the models of reliable manufacturers is very durable and designed for long service life.
Brass and aluminum are considered more reliable, while the cost of products made from them is much higher. Usually, professional sink bodies are made from these materials. However, the body material is far from the only guarantee of the reliability of the device, so when choosing a sink, you should not rely solely on this characteristic.
Complete with high-pressure washers is usually a set of nozzles designed for different purposes. The fan nozzle sprays water widely. It is suitable for washing large and not very dirty objects – walls or garden paths, with its help, it is convenient to wash the foam from the car.
For very severe contaminants, rotary nozzles are used that wash dirt by contact, and mud cutters. Sometimes the manufacturer also adds a nozzle for cleaning pipes to this kit.
A pressure washer cleaner is undoubtedly a useful unit in everyday life but requires increased attention to itself. When used properly, it saves money and helps keep the car clean. Her purchase pays off in the first year. The nomenclature of such devices in the Russian market is wide enough to satisfy any category of consumers.
I’m John Martell who has a passion towards making the lives of other people better. Throughout my life experiences, I have learned numerous techniques, which can be used to make other people better. You will, therefore, be able to follow the techniques that we offer and get the most out of what we can provide to you in the long run. That’s the main reason why I decided to start this blog as well. You can go through this blog and see how I’m helping you to get your cleaning work done in an effective and efficient manner.
Go ahead and contact me if you have anything to ask. I’m more than happy to listen to you and provide you with the support and assistance that you need.